Long (Wasted/Drilled) SOHC Rear Magneto Nut (Pre-Featherbed Type) - Stainless Steel: EachProduct no.: 1170 E3837This listing is for a 'Long Length' magneto bolt/nut - of the type that were fitted on the rear fitting of the magneto platform on SOHC Norton engines. This type of 'wasted' extra long nut were designed this way - because then they would protrude down beyond the rear engine plates, and so be easily accesable - to allow for magneto chain adjustment. This extra long type were fitted to all Pre-Featherbed SOHC models. They are CNC bar turned to the original 'wasted and 'drilled' dimensions of the original, in the correct imperial Hex stainless steel. See detail listing for more information. Price is Each
|
Featherbed Type Med Length (Wasted/Drilled) SOHC Rear Magneto Nut - Stainless Steel: EachProduct no.: 1171 E3837FThis listing is for a Featherbed type 'Long Length' magneto bolt/nut - of the type that were fitted on the rear fitting of the magneto platform on SOHC Norton engines. This bolt is similar to our Item 1170, but the rear magneto mounting nut on Featherbed road models (i.e Featherbed International) were of this shorter length than the pre-Featherbed type. They are CNC bar turned to the original 'wasted and 'drilled' dimensions of the original, in the correct imperial Hex stainless steel. See detail listing for more information. Price is Each
|
Norton (Engine Side) Magneto Sprocket Nut - SOHC Rev Clock Drive Type. Stainless Steel: EachProduct no.: 1187 A11M/80This listing is for the special slotted end nut that retained the engine side magneto sprocket on those SOHC sports and competition models - fitted wtih the outer timing cover that had a Rev Clock Gearbox fitted. These are CNC machined by us in Stainless Steel. See Listing for more information on fitting. Price is Each |
Norton (Engine Side) Magneto Sprocket Nut - Std Type. Stainless Steel: EachProduct no.: 1186 A11/80This listing is for a stainless steel mgneto sprocket (engine side) nut as fitted to the SOHC oil drive gear spindle, or the OHV/SV camshaft spindle. These nuts are same thread and dimensions as original. Price is per nut |
Lucas Mag/Dyno Magneto Shouldered Sprocket Nut - All Road Models. EachProduct no.: 1188 24-0195This listing is for the special shouldered sprocket nut that was fitted to Lucas Mag/Dyno units - on all roadgoing Norton single cylinder models (but also many other makes of British motorcycles using a Lucas Mag/dyno unit, original part number 24-0195. This nut is plated steel. Price is Each |
SOHC Magneto Chain (Genuine Renolds) + Soft Link : SOHC Models (46 Link)Product no.: 0393 A11/113Genuine Renolds magneto chain and one soft link, to fit SOHC 500cc and later 350cc engines. Note, these chains should use a riveted (soft link), not a circlip link. Can also be used on later OHV/SV models. See detail listing for more information |
Spare Magneto Chain Soft/Rivetable Link (all Norton Single Models) - Renolds MakeProduct no.: 0394 A11/113RThis item is a genuine Renolds 'soft' link to fit a magneto chain. This type of rivetable link is always preferable to a 'split' type link and would have been fitted orignally. All our Norton magneto chains come supplied with one of these 'soft/rivetable links, but we also sell them separtely here - and it is often handy to keep a couple in your toolbox. See listing for details. Price is per soft link and plate. |
Magneto Chain Split Link (Renolds)Product no.: 0395 A11/113SThis item is a Renolds 'split' link to fit a magneto chain. |
Magneto Chain Link and Half (Renolds)Product no.: 0432 A11/113HFirst and foremost i would say it is not recommended to fit a half link (or link and a half as it actually is), but I know that on some rare occasions you may have an unusual timing covers where the chain can either be too slack/tight with standard links. Therefore this item is for a Reynolds link and a half to fit Norton magneto chains |
Norton SOHC - Crankcase Bevel Pressure Release Pipe (Breather Pipe)Product no.: 0627 A11/717Breather Pipe (listed in Norton 1948 catalog as Pressure Release Pipe) and 1/4" BSP union nut to fit bevel chamber of all SOHC models (30/40, M30/M40 etc) |
71 - 80 of 99 results |
|