1.h Norton SOHC and OHV/SV Petrol and Oil Tank Parts

A selection of petrol and oil tank parts - including taps, original type oil and petrol pipes and fittings and mounting rubbers and stainless fastenings.

Note that many of our tank bolt and rubbers sold as SOHC International, were also of the same design as those fitted to most OHV and Side Valve Norton singles

Display per page

Sort by

61 - 70 of 81 results

Norton International - 2.5" Butterfly Oil Filler Cap (and OHV/SV Petrol Tank) Product no.: 0120b A11/291 - Modern Reproduction of the classic 2.5" butterfly filler cap, as used on Norton International oil tanks (as well as pushrod and sidevalve petrol tanks). Notice: £35.00 * In stock	Norton International - 2.5" Butterfly Oil Filler Cap - HD Quality Product no.: 0120b_HD A11/291 - Modern Reproduction of the classic 2.5" butterfly filler cap, as used on Norton International and SOHC Manx oil tanks (as well as pushrod and sidevalve petrol tanks). This item is the same as 0120b except it is UK made and of a slightly higher quality than the other type. It comes supplied with rubber seal. I also sell cork style replacement washers (Item 0466) if you prefer to use that type. £40.00 * In stock	Norton CS1/ES2/16H - 2" Butterfly Oil Filler Cap (Each) Product no.: 0120c A2/291 Smaller 2" butterfly oil filler cap, as fitted to Norton CS1 (none International) and pushrod/sidevalve Nortons from 1930's through to the 1950's. Comes with cork washer fitted (which many from other sources do not!) £32.00 * In stock
Cork Washer for 2" Butterfly Cap Product no.: 0465 A2/291W This is a replacement cork sealing washer to fit the 2" butterfly cap fitted to Norton OHV/SV oil tank caps (the caps can be ordered separately - Item 0120c) £1.90 * In stock	Cork Washer for 2.5" Butterfly Cap Product no.: 0466 A11/291W This is a replacement cork sealing washer to fit the 2.5" butterfly cap fitted to Norton International/SOHC Manx oil tanks and OHV/SV petrol caps (the caps can be ordered separately - Item 0120b and 0120b_HD). It is approximately 63mm outer diameter £2.80 * In stock	Oil Tank Bracket for International - Central (Up To 1948) Product no.: 0212a A11/297a - Fabricated bracket that secures Internatonal half curve oil tank to the frame bracket underneath the saddle - This item is lasercut to the same pattern as shown in the 1989 Norton catalog. Note the pre-war up to 1948 oil tank is visually very similar to the post 48 oil tank, but is easily identifiable because the left battery side is completely flat, without the indented panel of the later tank, see the second photograph £20.00 * In stock
Oil Tank Bracket for International - Offset (Post 1948) Product no.: 0212b A11/297b - Fabricated bracket that secures Internatonal half curve oil tank to the frame bracket underneath the saddle - This item is lasercut to the same pattern as shown in the 1949 Norton catalog and is copied from an original item. Note the post 1948 oil tank is visually very similar to the earlier oil tank, but is easily identifiable because the left battery side has an indented panel, see the second photograph £20.00 * In stock	Oil Tank Bracket for Manx Wrapround - Central Fitting, Long Product no.: 0213 A11M/297 - Fabricated bracket that secures Manx wrapround oil tank to the frame bracket underneath the saddle - This item is lasercut to the same pattern as shown in the 1948 Norton catalog. Note: this bracket is approximately 8cm between centres, it does not fit the 1949-50 style alloy Gardengate tank, which has wider (bolthru) centres and is approximately 14cm between centres. That particular bracket was made from steel tube (similar to used on mudguard stays) with a gradual curve - and a steel bracket welded to the centre of this tube that goes to the rear of the mudguard. . . sorry I do not make that particular bracket £21.00 * In stock	Norton Oilbath Chaincase Inspection Cover - Cork Oil Washer Product no.: 0379 A2/488 Cork washer that fits behind hte Chaincase inspection Cover (our Item no 0378). Prevents oil weep down side of chaincase! £2.80 * In stock
Spare Nitrile 'O' Rings For Norton 'Oiler' shaft - Pack of 3 Product no.: 0573 Oring02 These are 4mm internal ID Nitrile O rings and are fitted onto the shaft of the Norton Oilers (Item 0570 and 0571) just under the top brass ferrule, and one is fitted to stop excess oil travelling up the shaft. These are replacement O rings which can be fitted if the original O ring gets worn, or you damage the original if stripping to clean old castor oil. The original 'Oilers' were normally fitted wtih a form of rubber/leather washer at the same point - and I would expect that either one or two of these modern O rings would make a good replacement. Sold as a pack of 3 £1.80 * In stock