This section includes many parts to fit original BTH KD1 competition magnetos (as fitted to the majority of competition Norton SOHC models), as well as other parts for competition Lucas magnetos and roadoging Mag/Dyno's.
It also contains a selection of period veteran and vintage HT leads, spark plugs and spark plug accessories.
See also section 3.b for general electrical components and wiring system for your motorcycle
BTH KD1/ Lucas Mag/Dyno and Other Norton Single Electrical PartsProduct no.: 0176 Info5The BTH KD1 Competition magneto was the standard fitment to competition Norton Internationals and SOHC Manx Nortons. The competition versions (identified by a brass plate on its side reading either 'TT Magneto' or 'Dirt Track Magneto' and having the icompetition designate in its serial number) were fitted with platinum points and a manual advance/retard mechanism with a 3 screw inspection cover. I can supply most parts to fit this magneto and also occasionaly I have second hand parts as well. PLEASE NOTE: Some of the prices quoted in this section - particularly for small stainless steel screws may seem expensive compared to other commercially available nuts and bolts. Please bear in mind that this is because they are being made specially in small batch's for this magneto. Unfortunately the machinist charges for the number of machining operations - not the size of the screw!! |
Norton 15 Tooth Magneto Sprocket - Magneto Side (Lucas and BTH Magneto fitting) - EachProduct no.: 0392 A11/112This item is the 15 tooth magneto sprocket that was fitted to most Norton single cylinder models from the 1930's to late 1950's (i.e. SOHC, OHV and SV models) and fits on the end of the magneto shaft (either Lucas Magdyno or BTH KD1 fitment). These items are just the same in profile as original sprockets - the magneto sprocket being recessed, just as the original Norton item. Price is Each. |
Norton 15 Tooth Magneto Sprocket - Engine Side (SOHC/OHV/SV) - EachProduct no.: 0391 A2/79This item is the 15 tooth Norton single magneto chain sprocket on the engine side - that drives the chain to the magneto sprocket, it fits on the end of the oil pump drive gear (SOHC models) or inlet cam (OHV and SV models). These sprockets are manufactured to to the original Norton profile, and were as used on most Norton single cylinder models (i.e. SOHC, OHV and SV singles) from the 1930's to late 1950's. Price is Each. |
BTH KD1 Magneto - Contact Breaker Set (Standard /Tungsten Type)Product no.: 0185 KD1 016- High quality 'Standard' type (i.e. Tungsten tips, not platinum) tungsten BTH KD1 Contact Breaker Points Set, from trusted UK supplier |
New BTH KD1 Magneto - Platinum Contact Breaker Set (Original TT/Competition Type)Product no.: 0185b KD1 016b- Proper Competion PLATINUM BTH KD1 Contact Breaker Points Set These are the correct platinum contact breakers, as were originally fitted to genuine competition KD1 magnetos, Update July 2024: Just a handful of these genuine platinum points have just come in . . . probably for the last time! . . . see listing for more detail |
Aluminium 'BTH' Embossed Cover to fit BTH KD1/MH1/KD2 and other similar BTH magnetos - EachProduct no.: 0868 KD1_032- This is an excellent reproduction of the aluminium cover that was fitted to many BTH magnetos from the 1920's - late 1950's, including the KD1, MH1, KD2 and other similar models. It has a faithful reproduction of the correct BTH motif stamped into it. Aluminium. Price is Each |
BTH KD1 Comp Magneto - Lockwired Housing Screws : Stainless SteelProduct no.: 0189 KD1 009- Stainless steel hex head tapered screws for competition BTH housings. Drilled to take lockwire and with screwhead slot, just as the originals were - Stainless Steel. Price is each |
BTH KD1 TT - 3 Point Competition Points Cover - Unmachined Alloy Casting with DrawingProduct no.: 0983 KD1_TTCap1This listing is for an unmachined cast aluminium 3-screw type points cover, to fit the manual advance/retard housing BTH KD1 TT model magneto. The casting is a high quality (lost wax) casting, with (lathe) machining boss attached, and we supply it with an engineering drawing giving machining dimensions taken from an original cover. See listing for further detail |
BTH KD1 Magneto - Competition Cover Hex Slotted Screw/Washer - Stainless Steel (Each)Product no.: 0187 KD1 008Hex head bolt with screwdriver slot to fit the 3-point competition BTH KD1 cover (screw comes with steel washer) |
BTH KD1 Magneto - Alloy BTH Cover - Securing Side Screws and Washers - Stainless Steel (Pair)Product no.: 1096 KD1 0033These are the small round headed screws that retain the alloy BTH embossed cover fitted to most BTH magnetos, as shown here. Screws are CNC turned in stainless steel to original BTH head shape, and come with washers. Price is per pair |
BTH KD1 Magneto - Competition Inspection Cover Paper WasherProduct no.: 0188 KD1 013- Competition Cover (3 screw type) paper gasket for BTH KD1 competition magnetos |
BTH KD1 (and other types) Magneto - Rear Bearing Housing Shims (4 or 8 Thou thick): Price is EachProduct no.: 0179 KD1 017- Correct size shims to fit BTH KD1 magnetos and other BTH magnetos with similar housing - i.e. KD2, KH1, KH2 etc. See detail listing for more information. Available in 2 thickness - state which required. Also, see detail for Lucas size shims |
BTH KD1 Magneto - HT Pick Up Screws + Washer: Original BTH Form (Stainless Steel) - EachProduct no.: 0182 KD1 005- Stainless Steel Pick Up screws to fit BTH KD1 and other BTH magnetos - in the correct wide base, shallow profile of the BTH original items, in stainless steel with washer and lightly polished head (Each - screw and washer) |
BTH KD1 Magneto - HT Pick UpProduct no.: 0180 KD1 003- Good quality Reproduction KD1 pick up to fit BTH KD1 magnetos (Note: does not include pickup brush shown in photograph). Price is Each |
BTH KD1 Magneto - HT Pick up Rubber coverProduct no.: 0181 KD1 004- Ruubber cover that fits over pick up and HT Lead on BTH KD1 and most other BTH magnetos - essential to protect from damp/petrol etc |
BTH KD1 Magneto - HT Pick Up FerrulesProduct no.: 0183 KD1 006- Graphite HT Pick Up ferrules with spring attached (these are frequently worn on used magnetos) - I find that if this needs replacing, it also benefits to clean the slip ring contact. Great care should be taken when doing this not to damage the slip ring |
BTH KD1 Magneto - HT Pick Up Base Gasket: Cork - EachProduct no.: 0184 KD1 018
- Cork gasket that fits at base of KD1 HT pick up
£2.90
*
|
BTH KD1 Magneto - Points Plate Earth BrushProduct no.: 0186 KD1 007- Earth brush and spring that fits in the back of the Points plate on BTH KD1, MD1 and similar BTH magnetos |
BTH KD1 Comp Magneto - Advance/Retard Housing Lower PlugProduct no.: 0190 KD1 011- This is the large width housing plug that fits into the bottom of the KD1 manual advance/retard housing, at the base of the cable mechanism, often missing (fitting it helps prevent corrosion and dirt entering the mechanism). Dull nickel plated as per original can be shipped within 10 days |
BTH KD1 Comp Magneto - Manual Advance/Retard Cable AbutmentProduct no.: 0191 KD1 012- Brass hex head cable abutment that screws into the top of the manual advance/retard housing cable mechanism on BTH KD1 magnetos. the cable adjuster then screws into this item |
BTH KD1 Competition Magneto - Manual Advance/Retard Plunger BodyProduct no.: 0192 KD1 015- Plunger for manual advance/retard unit on BTH KD1 magnetos, fitted with manual advance/retard mechanism. |
BTH KD1 Magneto - Armature BearingProduct no.: 0249 KD1001- Single row ball bearing to fit BTH KD1 competition magnetos (as fitted to Norton camshaft engines). I believe this bearing also fits other similar BTH single cylinder magneto's, i.e. standard KD1 and MH1 models |
BTH KD1 Magneto (and Lucas?) - Bearing InsulatorProduct no.: 0178 KD1 002- Insulator gasket to fit beahind BTH KD1 bearing. fits between bearing and housing. one required per bearing - required when building a magneto, to ensure it insulates bearing from body. Price is each (may also fit Lucas mags - check for details) |
BTH KD1 (and Lucas Manual Magnetos) - Advance/Retard Cable Abutment - Rubber Shroud (Each)Product no.: 0372 KD1 027
Rubber cable shroud to stop water running down the advance\retard cable and into the mechanism. This shroud is of the type fitted to BTH KD1 magnetos, but is also very similar to the Lucas variety as well (and can be used on both)
£3.30
*
|
Lucas Mag/Dyno and Other Lucas Mag Parts (Mainly to Fit Norton Models - but other makes too)Product no.: 0176x Info6The following section lists many of the consumables and necessary parts to refurbish Lucas Magnetos and Magdynos. See also our other electrical section for other wiring and lighting parts. |
Norton Singles Wiring Diagrams Doc + Two Lucas/Norton Spare Parts Lists (3 Docs - A4 Format)Product no.: 1213 WKM027This listing is for a bundle of 3 seperate documents: A RacingNorton publication giving a chronological list of the different Wiring Diagrams used on Norton singles from the early 1930s to 1962 (A4 format, 14 pages), a high quality facsimile of an original Lucas 1956 spare parts for Norton motorcycles pamphlet and finally an exert from an original Lucas 1957 Spare list - describing the Lucas parts used on all Norton Models from 1936-57. These 3 documents are all produced in high quality colour A4 format and are very useful to the Norton restorer, as well as just providing an interesting read for any Norton enthusiast. Price is for all documents
|
Lucas M01L (Mag/Dyno) Face Cam Magneto - Contact Breaker SetProduct no.: 1012 LUC030- High quality tungsten Contact Breaker Points Set to fit the popular Lucas M01L type Face Cam Mag/Dyno magneto, as fitted to most roadgoing Norton singles, from trusted UK supplier |
Lucas M01L (Mag/Dyno) and other Lucas Magnetos -HT Pickup Brush and Spring - EachProduct no.: 1219 LUC037- These are the rectangular brushes fitted to the Lucas E3 and E3L Dynamo unit that sits atop the Lucas Magdyno unit, fitted to most Norton Single Cylinder roadgoing models. These brushes are to fit the E3(L) 2 brush type dynamo, fitted to Norton models from 1937 onwards. See detail listing for more information. Price is Per Pair |
Lucas M01L (Mag/Dyno) -Earthing Brush and Spring - EachProduct no.: 1220 LUC038- This listing is for the (armature) Earthing Brush and spring fitted to those Lucas Magdyno M01L magnetos that were fitted with earthing brushes - i.e. with a brass earthing side screw, as shown in the accompanyning photos. Price is for brush and spring. |
Lucas Magdyno M01l, NR1 and K2FC - HT Pickup Gasket - EachProduct no.: 0315 2948This is the thick gasket that fits underneath the HT pickup fitted to most Lucas Magdyno magnetos, as well as Lucas NR1 and K1F/K2FC/KVFTT competition magnetos. These are high quality UK manufactured gaskts. Price is Each. |
1 - 30 of 97 results |
|