1.m Handlebars, Controls, Cables

1.m Handlebars, Controls, Cables

1.m Handlebars, Controls, Cables
This section lists control fittings such as handlebars, brake and clutch levers, cable fitings etc

Display per page
Sort by
31 - 60 of 60 results

Front Number Pate

Product no.: 0584 A2/531

Front Number plate, painted with a black finish.

This number plate has a sporty rake on on one side (which would be facing the rear of the bike.  However - if you prefer the symetric shape that was adoped on some bikes (i.e. the Vincent used a symetric front number plate commonly), then it is a simple job to copy the shape of the other end onto a cardboard template and then use this as a template to help cut away the 'rake' part on the other end, leaving a symetric style plate.  I have done this with one of these plates when fitting one to my Vincent Comet restoration

£8.50 *

Rev Clock Cable - 36"

Product no.: 0340 A11M\552

To go with the parts above, a 36" rev clock cable, which I have found to be the ideal size for the Norton rev clock timing cover's shown here, going to a rev clock mounted on the top of girder forks.

£19.50 *

Dolls Head Gearbox - Gear Indicator

Product no.: 0273 A2/404
This distinctively shaped item was used on all dolls-head and upright gearbox's to show what gear you were in. As with all my other lasercut items, this is copied from an original item and the bends have been replicated faithfully as well
£5.50 *

Norton Footrest Rubber - Pair

Product no.: 0209R A2\507
Pair of classic Norton 'D' shaped footrest rubbers
£13.00 *

Gearchange Rubber

Product no.: 0338 A11M\407

Period gearchange rubber, similar in design to the one shown in the 1948 Norton Spare Parts Catalog as fitted to the Plunger Manx gearchange lever.

£2.50 *
In stock
can be shipped within 30 days

Gearchange Rubber - Late (alternative) Type

Product no.: 0617 A11/407

Good quality gearchange rubber - of type used in the 1950's. 

£2.80 *
In stock

Smiths Speedo/Rev Clock Chronometric Bezel Ring

Product no.: 0406 Speedo_01
Chromed bezel ring to fit all Smiths/Jaeger (80mm diameter) chronometric Speedometers and Rev Clocks. This is a high quality, UK made item. In the attached photos a genuine pre-war 120mph Smiths/Jaeger chronometric (it was originally fitted to a 1937 Norton International) speedo is used to give scale to the item and was used for testing all speedo items shown in this section
£18.00 *

Smiths Speedo/Rev Clock Chronometric Lipped Bezel Ring

Product no.: 0407 Speedo_02
Chromed and lipped bezel ring as used on Smiths (80mm diameter) chronometric Speedometers that would be mounted into binnacles and headlamp shells. The lip prevents the speedometer from dropping through the binnacle, and the speedometer is normally held in place by using a 'U' bracket from behind. I include a picture of my Royal Enfield Constellation which is fitted with an orignal 150mph Smiths speedo with a lippeed ring. This is a high quality, UK made item,
£18.00 *

3mm Glass for Chronometric Speedo/Rev Clock

Product no.: 0408 Speedo_03
This is a replacement glass for a chronometric (80mm) speedo or rev clock. It is 3mm thick, as per all early (1930s - 50's?) clocks. Nicely finished edges on glass (unlike some cheaper glasses I have seen)
£3.30 *

2mm Glass for Chronometric/Magnetic Speedo/Rev Clock

Product no.: 0409 Speedo_04
This is a replacement glass for a chronometric or magnetic (80mm) speedo or rev clock. It is 2mm thick. I am not entirely sure what 2mm glass was used for, but suspect it was fitted to later type Smiths speedos/rev clocks of the 50's-60's, maybe the magnetic type. Check your original glass if not sure
£2.80 *

Glass Support Ring for Chronometric Speedo/Rev Clock

Product no.: 0410 Speedo_05
This is the recessed ring that fits snugly into the top of the speedo/rev clock case on chronometric (80mm) instruments and holds the glass in place. This is a nice quality item with a pretty plated finish. Often, when stripping an original instrument this item will found to be in poor condition, for which this is an ideal replacement. In the accompyaning photograph you can see an original pre-war Norton International speedometer, to which I have fitted one of these rings
£7.00 *

Chronometric Under Bezel 'O' Ring

Product no.: 0411 Speedo_06
This is the NBR060 'O' ring that fits in the recess under the chrome bezel of chronometric speedo/rev clocks. It ensures a watertight seal against the glass
£2.00 *

3mm Diameter Neoprene Sponge Cord - 20" Length

Product no.: 0412 Speedo_07
This 3mm diameter Neoprene sponge cord can be used under the bezel rings of chronometric and magnetic speedo/rev clocks of all sizes, in a similar manner to the O ring (Item number Speedo_06). It is supplied in a 20" length that can be cut to size, but this length should be sufficient to complete two 80mm (standard chronometric size) instruments. The sponge cord material is slightly softer than the O ring material
£2.00 *

Speedometer Threaded Brass Insert - Light Holder

Product no.: 0413 Speedo_08
If you have a very early (i.e. pre-war) type speedometer or rev clock case, then it may not have provision for a light bulb. By drilling a suitable size hole and then soldering this brass ring in, this will allow the standard Smiths light bulb holder to be fitted
£3.30 *

Chrome Trip Knobs

Product no.: 0414 Speedo_09
These are very nice chrome, straight knurled, knobs that were fitted to the end of the 'Trip' shaft, so the trip meter could be reset. They are very nice quality and are drilled so they can be attached to the trip shaft by means of a small split pin, as per originals. Often the trip knobs on original speedometers are missing, this will really set the speedometer off
£6.00 *

Chronometric Trip Shaft

Product no.: 0415 Speedo_10
This is the shaft that is fitted to the rear of the chronometric peedo mechanism on one end and allows the chrome trip knob to be fitted on the other end. This item is very nicely made
£5.00 *

Rev Clock/Speedo (Chronometric) Back Screws (Pair)

Product no.: 0636 Speedo_11

Pair of screws used to secure the internal mechanism of Smiths Chronometric Rev Clocks and Speedo's to the case.  

£2.40 *
In stock

Smiths type 80mm Screw on Chronomatic Flanged Top Ring - Chromed

Product no.: 0637 Speedo_12

Smiths type 80mm Screw on Chronomatic Flanged Top Ring - Chromed, to fit those Speedos that are mounted in nacelles.

£18.00 *
In stock

80mm Chronnometric Rev Clock Case (no illumination) for Smiths Rev Clock

Product no.: 0638 Speedo_13

High quality reproduction 80mm Chronnometric Rev Clock Case (no illumination) for Smiths Rev Clock

£26.00 *
In stock

Rev Clock/Speedo (Chronometric) Pointer - Early Type with Through Hole

Product no.: 0643 Speedo_14

Chronometric speedometer or rev clock Needle - early type with through hole 

£15.00 *
In stock

Rev Clock/Speedo (Chronometric) Front Gasket

Product no.: 0644 Speedo_15

This is the paper gasket that fits behind face of Smiths rev clocks/speedos - as originally manufactured

£2.50 *
In stock

Rev Clock/Speedo (Chronometric) Black Face Retaining Screws - Pack of 4

Product no.: 0646 Speedo_17

Chronometric speedometer or rev clock - Black face retaining screws - pack of 4 

£5.00 *
In stock

Rev Clock/Speedo (Chronometric) Back Gasket

Product no.: 0645 Speedo_16

This is the paper gasket that fits at the back of Smiths rev clocks/speedos, between the mechanism and the case - as originally manufactured

£2.50 *
In stock

Rev Clock/Speedo (Chronometric) Black Face Retaining Screws - Each

Product no.: 0647 Speedo_18

Chronometric speedometer or rev clock - Black face retaining screws - Each

£1.50 *
In stock

Telescopic (Es-Way Replica) Prop Stand

Product no.: 0615 Stand3

This is a beautifully made copy of the original pre-war Es-Way telescopic prop stand - a great add on for any 1920's-1950's British rigid (and possibly plunger) motorcycle and a period piece that would like great and in keeping on your roadgoing Norton International - or any rigid Norton for that matter!  

£145.00 *
In stock

OHV/SV/Dominator Rigid/Gardengate/Swing Arm: Brake Pedal Pivot Bolt and Nut

Product no.: 0652 A2/502

Stainless Steel rear brake pedal pivot bolt and nut to fit OHV and Side Valve siingle cylinder models, and all pre Featherbed roadgoing models.  This is the pivot bolt that screws into the frame from which the rear brake pedal pivots

£24.00 *

SOHC International Model 30/40: Brake Pedal Pivot Bolt and Nut

Product no.: 0653 A11/502

Stainless Steel rear brake pedal pivot bolt and nut to fit SOHC International models (Model 30 and Model 40) for Rigid and Gardengate framed models. This is the pivot bolt that screws into the frame from which the rear brake pedal pivots

£24.00 *
In stock

SOHC M30 (Gardengate Manx type): Brake Pedal Pivot Bolt and Nut

Product no.: 0654 A11/502M

Stainless Steel rear brake pedal pivot bolt and nut to fit SOHC M30/M40 (i.e. pre-Featherbed Manx type) for Rigid and Gardengate framed models. This is the pivot bolt that screws into the frame from which the rear brake pedal pivots

£24.00 *
In stock

1/4" BSF Forged Nut - Stainless: Pack of 10

Product no.: 0490F 0250FORG

Pack of 10 1/4" BSF stainless steel nuts - commercially available forged type, fractionally smaller width than our 'full nut' type, but often better for smaller bolts and cheaper.  same TPI as BSC bolts and interchangeable

£5.00 *
In stock

1/4" BSC Full Nut - Stainless: Pack of 10

Product no.: 0490 0250FNSS

Pack of 10 1/4" BSC stainless steel nuts - higher quality 'Full nut' than most commercial types 

£7.50 *
In stock
*
Recommended Retail Price, plus delivery
31 - 60 of 60 results