1.e Norton SOHC Crankshaft Parts

1.e Norton SOHC Crankshaft Parts

1.e Norton SOHC Crankshaft Parts
Norton SOHC Crankshaft parts including Conrod and Bigend

Display per page
Sort by
46 - 63 of 63 results

Crankcase Breather - Fibre Washer

Product no.: 0249 A11/719FW

Surprisingly it is very difficult to find good quality vulcanised (red fibre) washers to fit 1/4"BSP fittings. These red fibre washers are of the highest quality (from a specialist manufacturer) and have just the right external diameter - but are a very tight fit on the thread. To fit them I place the breather (or similar 1/4" BSP fitting) in soft jaw vice, then place these washers just onto the thread - then I carefully use a pair of large pliers (the circular hole with coarse teeth) to carefully wind them onto the thread. Although this is difficult - the result is the correct size washer that does not look out of place under a Norton breather (unlike many modern ones that are far too wide and look out of place). These are high quality washers from a top manufacturer - sold in pack of 5. Note: do not buy if you are worried you might not be able to fit them!!

£2.10 *

SOHC Crankcase Union/Sump Bolt Filter 1/4" BSP Copper Washer - Pack of 3

Product no.: 0090b E5264-C1

1/4" BSP Copper Washer - pack of 3. This washer is suitable for use in 3 places - the main Oil pipe unions that screw into the crankcase (see second photograph), the Oil filter bolt that fits at the base of the timing case chamber or the sump plug screw. 

£2.90 *

SOHC Crankcase Bevel Platform - Oil Return Blanking Plug/Washer (SS)

Product no.: 0660 A11/08X

Distinctive small hex blanking plug/bolt that locates on the left side on the crankcase lower bevel platfom.  CNC maufactured in stainless steel and includes red fibre washer 

£4.00 *
In stock

SOHC Oil Filter (Dowty) Washer

Product no.: 0090 E5264

- Modern equivelant Dowty washer (outer washer is zinc plated steel, inner washer is neoprene). This washer is used behind the timing chamber filter bolt and also at the back of the rear cylinder crankcase mouth bolt (that has an oil feed)

£1.00 *
In stock

Norton SOHC - Crankcase Bevel Pressure Release Pipe (Breather Pipe)

Product no.: 0627 A11/717

Breather Pipe (listed in Norton 1948 catalog as Pressure Release Pipe) and 1/4" BSP union nut to fit bevel chamber of all SOHC models (30/40, M30/M40 etc)

£9.00 *
In stock

Norton SOHC - Crankcase Bevel Pressure Release Pipe (Breather Pipe) - Long

Product no.: 0628 A11/717L

Breather Pipe (listed in Norton 1948 catalog as Pressure Release Pipe) and 1/4" BSP union nut to fit bevel chamber of all SOHC models (30/40, M30/M40 etc)

£10.00 *
In stock

Norton SOHC - M30 Front Crankcase Breather Pipe - Long Type

Product no.: 0630 A11M/720b

Breather pipe to fit breather union of type fitted to the front of drive side crankcase - most commonly fitted to magnesium M30 (and early pre-Featherbed Manx) crankcases 

£16.00 *
In stock

Norton SOHC - Crankcase Feed Pipe To Cambox

Product no.: 0631 A11M/789b

Crankcase feed pipe to cambox and 1/4" BSP union nut's to fit all SOHC models (30/40, M30/M40 etc) - this is the bottom piece of the cambox feed pipe assembly - which we offer here to be purchased seperately

£8.00 *
In stock

Lockwire - 12" length of Stainless Steel Lockwire

Product no.: 0632 Lckwre1

Lockwire:  12"/(approx) 300mm length of Goodrich stainless steel lockwire, for lockwiring breather pipes

£0.90 *
In stock

Cambox Feed Pipe Assembly - Black 5/16 Oil Pipe (4.5" / 110mm Length)

Product no.: 0633 BrthrPipe1

Black (original rubber style) 5/16" oil reistent pipe for cambox feedpipe assembly - 4.5"/110mm length

£1.60 *
In stock

Black 5/16" Oil Pipe/Breather Pipe - 3ft / 900mm Length

Product no.: 0634 BrthrPipe2

Black (original rubber style) 5/16" oil reistent pipe for use for oil breather pipes, oil pipes (or even big bore fuel pipes if required - although 1/4" bore pipe is more normally used) - 3 foot /900mm length

£10.50 *
In stock

Black 5/16" Oil Pipe/Breather Pipe - 3ft / 900mm Length (non-Ethanol)

Product no.: 0634b BrthrPipe4

Black (original rubber style) 5/16" oil reistent pipe for use for oil breather pipes, oil pipes (or even big bore fuel pipes if required - although 1/4" bore pipe is more normally used) - 3 foot /900mm length

£9.00 *
In stock

7/16" Stainless Steel Engine Bolt Washer - Reduced Outer Diameter: Bag of 10

Product no.: 0661 7_16_ROD

7/16" Stainless Steel Engine Bolt Washers, but with Reduced Outer Diameter, which are correct for Norton 7/16" engine bolts as used on SOHC engines: Price is for bag of 10

£2.00 *
In stock

1/12" Stainless Steel Engine Bolt Washer - Reduced Outer Diameter: Bag of 6

Product no.: 0662 1_2_ROD

1/2" Stainless Steel Engine Bolt Washers, but with Reduced Outer Diameter, which are correct for the front Norton 1/2" engine/frame bolt as used on SOHC engines (as well as other 1/2" bolts where you do not want to fit a standard wide type washer : Price is for bag of 6

£2.50 *
In stock

SOHC E3224 3/8" x 26tpi BSC Engine Bolt Nut - Stainless Steel

Product no.: 0667 E3224_1

This is the E3224 3/8" x 26 tpi BSC engine nut as fitted to many Norton engine bolts.  It has the correct 'reduced head' and greater depth than other commercially available nuts of this thread/size - and is CNC made specially by us for fitting to Norton engine bolts, but in stainless steel 

£1.80 *
In stock

SOHC 13294 M30/M40 3/8" Engine Plate Top Bolt/Nut Set - Stainless Steel

Product no.: 0668 13294

This is the special 13294 front engine plate top bolt that is fitted to M30/M40 (pre-Featherbed Manx) magnesium engines.  It has the correct 'reduced' head 0.600" AF hex head, with distinctive Norton curved head finish.  This set comes complete with correct matching E3224 nut and two washers, all in stainless steel. It is 3/8" shaft diameter  

£18.00 *
In stock

SOHC E3238 7/16" x 20tpi Engine Bolt Nut - Stainless Steel

Product no.: 0669 E3238

This is the E3238 7/16" x 20 tpi engine nut as fitted to many Norton engine bolts.  It has the correct 'reduced head' and greater depth than other commercially available nuts of this thread/size - and is CNC made specially by us for fitting to Norton engine bolts, but in stainless steel 

£2.00 *
In stock

SOHC 10410 M30/M40 7/16" Engine Plate Lower Bolt/Nut Set - Stainless Steel

Product no.: 0670 10410

This is the special 10410 front engine plate lower bolt that is fitted to M30/M40 (pre-Featherbed Manx) magnesium engines.  It has the correct 'reduced' head 0.600" AF hex head, with distinctive Norton curved head finish.  This set comes complete with correct matching E3238 nut and two washers, all in stainless steel.  It is 7/16" diameter shaft 

£19.00 *
In stock
*
Recommended Retail Price, plus delivery
46 - 63 of 63 results