1.i Norton SOHC Petrol and Oil Tank Parts

1.i Norton SOHC Petrol and Oil Tank Parts

1.i Norton SOHC Petrol and Oil Tank Parts
Norton SOHC Petrol/Oil Tank Parts and Pipe Fittings

Display per page
Sort by
46 - 60 of 60 results

'Norton' Kneepads Fixing Screw - Pair

Product no.: 0478 E6629

These chromed fixing screws are copies of the original, used to secure the Norton kneepads (Item 0394)to the petrol tank. Price is for a pair (i.e. 2) screws.

£5.00 *

SOHC/DOHC M30 Racing Oil Tank Oiler - Front Type

Product no.: 0570 A11/854M-F

This is an exact replica of the very distinctive racing type oil tap (or 'Oilers' as they were commonly known) fitted to both Pre and Post war racing M30/Manx Norton wrapround tanks.  

£145.00 *
In stock
can be shipped within 10 days

SOHC/DOHC M30 Racing Oil Tank Oiler - Rear Type

Product no.: 0571 A11/854M-R

This is an exact replica of the very distinctive racing type oil tap (or 'Oilers' as they were commonly known) fitted to both Pre and Post war racing M30/Manx Norton wrapround tanks

£145.00 *
In stock
can be shipped within 10 days

New SOHC/DOHC M30 Racing Primary Chain Oiling Pipe & Bracket

Product no.: 0655 A11/855

This is the bracket and rubber oil pipes that fits to the driveside rear engine plate on Rigid and Gardengate M30/Manx Nortons, allowing oil from the oil tank front primary oiler to be fed onto the primary chain

£15.00 *
In stock
can be shipped within 10 days

Fibre Washers For Norton Oilers - Pack of 4

Product no.: 0572 FW012

These are (vulcanised) red fibre washers to fit the 1/8" BSP thread on the Norton Oilers (Item 0570 and 0571).  If you are purchasing the oilers - then they already come supplied with the red fibre washer, but these can be used if you want additional spacing (to ensure you can adjust them to tighten into just the right position without stressing the thread), or if you have original oilers or other 1/8" BSP connectors that need new washers.  As always, these washers come from a high quality specialist supplier and are 1mm thick.  They come supplied in a pack of 4

£1.60 *

Spare Nitrile 'O' Rings For Norton 'Oiler' shaft - Pack of 3

Product no.: 0573 Oring02

These are 4mm internal ID Nitrile O rings and are fitted onto the shaft of the Norton Oilers (Item 0570 and 0571) just under the top brass ferrule, and one is fitted to stop excess oil travelling up the shaft.  These are replacement O rings which can be fitted if the original O ring gets worn, or you damage the original if stripping to clean old castor oil.  The original 'Oilers' were normally fitted wtih a form of rubber/leather washer at the same point - and I would expect that either one or two of these modern O rings would make a good replacement.  Sold as a pack of 3

£1.40 *

Norton SOHC - Crankcase Bevel Pressure Release Pipe (Breather Pipe)

Product no.: 0627 A11/717

Breather Pipe (listed in Norton 1948 catalog as Pressure Release Pipe) and 1/4" BSP union nut to fit bevel chamber of all SOHC models (30/40, M30/M40 etc)

£9.00 *
In stock

Norton SOHC - Crankcase Bevel Pressure Release Pipe (Breather Pipe) - Long

Product no.: 0628 A11/717L

Breather Pipe (listed in Norton 1948 catalog as Pressure Release Pipe) and 1/4" BSP union nut to fit bevel chamber of all SOHC models (30/40, M30/M40 etc)

£10.00 *
In stock

Norton SOHC - Rocker Box Feed Pipe - Complete

Product no.: 0629 A11M/789

Complete Cambox Feed pipe and 1/4" BSP union nut's to fit all SOHC models (30/40, M30/M40 etc) - pipe length can be adjusted

£25.00 *
In stock

Norton SOHC - M30 Front Crankcase Breather Pipe - Long Type

Product no.: 0630 A11M/720b

Breather pipe to fit breather union of type fitted to the front of drive side crankcase - most commonly fitted to magnesium M30 (and early pre-Featherbed Manx) crankcases 

£16.00 *
In stock

Norton SOHC - Crankcase Feed Pipe To Cambox

Product no.: 0631 A11M/789b

Crankcase feed pipe to cambox and 1/4" BSP union nut's to fit all SOHC models (30/40, M30/M40 etc) - this is the bottom piece of the cambox feed pipe assembly - which we offer here to be purchased seperately

£8.00 *
In stock

Lockwire - 12" length of Stainless Steel Lockwire

Product no.: 0632 Lckwre1

Lockwire:  12"/(approx) 300mm length of Goodrich stainless steel lockwire, for lockwiring breather pipes

£0.90 *
In stock

Cambox Feed Pipe Assembly - Black 5/16 Oil Pipe (4.5" / 110mm Length)

Product no.: 0633 BrthrPipe1

Black (original rubber style) 5/16" oil reistent pipe for cambox feedpipe assembly - 4.5"/110mm length

£1.60 *
In stock

Black 5/16" Oil Pipe/Breather Pipe - 3ft / 900mm Length

Product no.: 0634 BrthrPipe2

Black (original rubber style) 5/16" oil reistent pipe for use for oil breather pipes, oil pipes (or even big bore fuel pipes if required - although 1/4" bore pipe is more normally used) - 3 foot /900mm length

£10.50 *
In stock

Black 5/16" Oil Pipe/Breather Pipe - 3ft / 900mm Length (non-Ethanol)

Product no.: 0634b BrthrPipe4

Black (original rubber style) 5/16" oil reistent pipe for use for oil breather pipes, oil pipes (or even big bore fuel pipes if required - although 1/4" bore pipe is more normally used) - 3 foot /900mm length

£9.00 *
In stock
*
Recommended Retail Price, plus delivery
46 - 60 of 60 results